Kyocera Mita/Taskalfa/Copystar Error Codes

Kyocera Mita/Taskalfa/Copystar Copiers and printers are equipped with a self diagnostic function. When a problem is detected, copying is disabled. “C” and a number between 0100 and 7810 alternates, indicating the nature of the problem. Kyocera errors are of three types. Some of them can be reset by turning the machine power switch off and back on while some others activate “partial operation control” disabling the defective part/area of the machine (paper feed cassette, stapler, document processor etc). If a specific unit is not working, perform U906 after taking measures against the cause of trouble to reactivate the unit.

Fixing error codes (C6xxx series) must be reset by a technician after clearing the cause of trouble. Reseting a fixing code without proper repair may result in fire or damage. (See how to reset fixing errors).

A general purpose error code list is given below. Use "Ctrl + F" to easily find your desired error explanation.

Error Code	Description
C0030	Fax PWB Problem. Processing with fax software is disabled due to software or hardware issues.
C0060	Main PWB Type Mismatch Error.
C0070	Fax PWB Incompatability Detection Problem. Fax software is not compatible with main PWB software.
C0130	Main PWB EEPROM Backup Memory Device Problem. EEPROM can not be written or read.
C0140	Main PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM.
C0150	Engine PWB EEPROM Backup Memory Device Problem. EEPROM cannot be written or read.
C0160	Engine PWB EEPROM Backup Memory Data Problem. Abnormal reading data from EEPROM. Read & write data do not match five times consecutively.
C0170	Copy Counts Problem. A checksum error is detected in the main and engine backup memories for copy counters.
C0180	Machine Number Mismatch Error. Machine number does not match on main and engine PWBs
C0600	Main PWB DIMM Installed Incorrectly.
C0610	Main PWB DIMM error
C0630	DMA transmission of compressed, decompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
C0640	Hard Disk Drive cannot be accessed
C0700	Optional CF backup is not suitable.
C0800	Image processing problem. JAM05 is detected twice.
C0830	Fax Flash ROM program area checksum error
C0870	Fax PWB to Main PWB high capacity data transfer problem.
C0880	Fax PWB program archive problem.
C0920	Fax backup data is not retained.
C1010	Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
C1020	Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms of overcurrent.
C1030	PF-700 optional cassette #3 lift motor error.
C1040	PF-700 optional cassette #4 lift motor error.
C1100	PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.
C1110	PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.
C1120	PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off after 30 seconds of motor operation.
C1130	PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off after 30 seconds of motor operation.
C1800	PF-700/PF-750 Communication Problem.
C1900	PF-700 EEPROM error. Write data & Read data are not in agreement three times consecutively.
C2000	Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected with 6 sec of activation.
C2250	Main Charge Cleaner Motor error. Lock error is detected three times in a row during cleaner motor operation.
C2500	Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor stability. Stabilization is not detected within 6 seconds of activation.
C2600	PF-700 Drive Motor error. Lock signal exceeds 500ms.
C2600	PF-750 Paper Conveying Motor error. Lock signal exceeds 450ms.
C3100	Scanner Carriage Problem. Scanner home position is not detected at initialization or start of copying from contact glass.
C3200	Exposure Lamp Problem. Exposure lamp does not reach the input value threshold within 5 sec of commencing reading.
C3210	Exposure Lamp Problem. Exposure lamp does not exceed the input threshold value within 5 sec of commencing reading.
C3300	CCD AGC Problem. After AGC correct input is not obtained at the CCD.
C3310	CIS AGC Problem. After AGC correct input is not obtained at the CIS.
C3500	Communication Error Between Scanner and SHD.
C3900	Scanner PWB Backup Memory Read/Write Problem. Read & Write data does not match.
C3910	Scanner PWB Backup Memory Data Problem. Data in a specified area of the backup memory does not match the specified values.
C4000	Polygon Motor Synchronization Problem. Polygon motor does not stabilize speed within 20 sec of activation.
C4010	Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec continuously after polygon motor stabilization.
C4200	BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec after polygon motor stabilization.
C5300	Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken wire detection signal is detected for 2 sec continuously.
C6000	Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec during warmup & ready. Thermistor2 detected less than 40C/104F for 10 sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at least 1C/1.8F within 5 sec.
C6020	Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected 250C/482F for 40ms or more.
C6030	Fixing Thermistor Break Error. Thermistor break signal is detected for 1 sec.
C6050	Abnormally Low Thermistor Temperature. Thermistor 1 is detected 80C/176F or less for 1 sec continuously during copying.
C6400	Zero-Cross Signal Error. While fuser heater On/Off control is performed, the zero-cross signal is not input within 3 sec.
C6410	Fuser Unit Connection Insertion Problem. Absence of fuser unit is detected.
C6420	Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse cut signal is turned on.
C7300	Toner Container Problem. Toner level is not detected when toner empty is detected.
C7400	Developing Unit Connection Insertion Problem. Absence of the developing unit is detected.
C7410	Drum Unit Connection Insertion Problem. Absence of the drum unit is detected.
C7800	Broken External Thermistor Wire. Thermistor on the environmental sensor outputs 4.5v or more.
C7810	Short-Circuited External Thermistor. Thermistor input value is 0.5v or less.
C7900	Drum EEPROM Error. Reading or writing to the EEPROM cannot be performed.
C7910	Developing EEPROM Error. Reading or writing to the EEPROM cannot be performed.
C8020	DF-710 Punch Motor Problem. Punch motor lock signal is detected for 500ms or more during activation.
C8030	DF-730 Tray Upper Limit Detection Problem. When tray elevation motor raises a tray, the upper limit switch detects On condition.
C8050	DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 1 does not turn On within 2.5 sec. Jam 88.
C8060	DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt home position sensor 2 does not turn On within 2.5 sec.
C8070	DF-710 Internal Tray Communication Error. The connection is detected, but communication is not possible with the internal tray.
C8140	DF-710 Main Tray Problem. Main tray is not detected in not detected by main tray top limit detection sensor or main tray capacity detection sensor within 20 sec of ascending. Main tray upper limit detection sensor or main tray load detection sensor is not detected as Off within 20 sec of main tray descending. Main tray lower limit detection sensor is not detected as On within 20 sec of main tray descending. Main tray upper limit detection sensor or main tray load detection sensor remain on for 2 sec or more during main tray ascent.
C8140	DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface view sensor cannot be detected within 10 sec.
C8170	DF-710 Side Registration Motor 1 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
C8170	DF-720 Front Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the front side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8170	DF-730 Adjustment Motor Problem. Adjustment motor home position motor is not detected within a specific time during activation.
C8180	DF-710 Side Registration Motor 2 Problem. During initial rotations home position is not detected within 3 sec. Jam 88.
C8180	DF-720 Rear Side Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the rear side home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8190	DF-720 Trailing Edge Registration Motor Problem. During initial rotations home position is not detected within 106 pulses. When the trailing edge home position sensor is turned off during initialization, the sensor did not turn on within 3 sec.
C8210	DF-710 Stapler Moving Motor 1 Error. During initial rotations home position is not detected within 1.5 sec.
C8210	DF-720 Finisher Stapler Problem. Stapler home position sensor does not change state from non-detect to detect within 200ms of forward (CCW) rotation. During initial rotations stapler home position detection does not change state from non-detect to detect within 600ms of reverse (CW) rotation.
C8210	DF-730 Stapler Problem. Home position is not detected within a specific time of activation.
C8220	DF-710 Stapler Moving Motor 2 Error. During initial rotations home position is not detected within 3.5 sec.
C8230	DF-710 Stapler Motor Problem. Jam 82 is indicated.
C8300	BF-710 Centerfold Unit Communiation Error. Although the connection is detected, communication is not possible with the centerfold unit.
C8310	BF-710 Centerfold Side Registration Motor 1 Problem. During initial rotations home position is not detected within 1000ms.
C8320	BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial rotations home position is not detected within 2500ms.
C8330	BF-710 Blade Motor Problem. During initial rotations home position is not detected within 1500ms.
C8340	BF-710 Centerfold Staple Motor Problem. Jam 89.
C8350	BF-710 Centerfold Side Registration Motor 2 Problem. During initial rotations home position is not detected within 1000ms.
C8360	BF-710 Centerfold Main Motor Problem. The motor lock signal is detected for more than 1000ms during activation.
C8440	DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be adjusted within the specified range.
C8460	DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot be performed.
C8500	MT-710 Communication Error. The connection is detected, but communication is not possible with the mailbox.
C8510	MT-710 Drive Motor Problem. The motor lock signal is detected for more than 500ms during activation.
C8800	DF-710 Communication Problem. No communication: there is no reply after (5) tries. Abnormal communication: a parity or checksum error is detected (5) times in succession.
C8900	DF-710 Backup Memory Data Problem. Read and write data does not match.
C8910	PH-5A Backup Memory Data Problem. Read and write data does not match.
C8920	MT-710 Backup Memory Data Problem. Read and write data does not match.
C8930	BF-710 Backup Memory Data Problem. Read and write data does not match.
C9000	DP-700 Communication Problem. A communication error is detected.
C9040	DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not detected within 10000 pulses. After a one time retry, the DP lift upper limit switch could not be turned On.
C9050	DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not detected within 10000 pulses. After a one time retry, the DP lift lower limit switch could not be turned On.
C9060	DP-700 EEPROM Error. Read and write data does not match. Data in the specified area of the backup memory does not match the specified values.
C9070	DP-700 Communication Error between the DP and SHD. A communication error is detected.
C9080	DP-700 Communication Error between the DP and CIS. Reading cannot be performed correctly.
CF000	Operation Panel PWB Communication Error/System Error. Unknown error. Communication error between panel and main controller. (If CF620 occurred and is left, CF000 also occurred because of timeout control.
CF010	Main PWB Checksum Error/System Error. Communication error between panel and main controller.
CF020	Memory Checksum Error/Operation System Error.
CF030	Main PWB System Error.
CF040	Engine PWB Communication Error.
CF041	Scanner PWB Communication Error.
CF050	Engine ROM Checksum Error.
CF060	Engine RAM Error.
CF070	Flash ROM Error. Defective flash ROM (which?).
CF080	Flash ROM Error (during download). Defective flash ROM (which?).
CF090	Fax System M Communication Error.
CF14F	Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
CF256	Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257	Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF26F	Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
CF3xx	Undefined.
CF423	Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CF423	Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451	HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470	HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494	HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF5xx	Undefined.
CF610	System Start Error.
CF620	System Error. Error acquiring the event data. Panel detects CF000 as same error.
CF620	System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
CF7D7	Readout Error of SSL (authentication data).
CFAxx	HDD Error.
CFB2C CFB30 CFB31	Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
CFB30	Incompatible Level Of Firmware on Main EEPROM.
CFB31	Corrupt Firmware on Main EEPROM.
CFB32	Panel Error. Timeout request for start up command. Start command hasn't been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB33	Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
F000	Operation Panel PWB Communication Error.
F010	Main PWB Checksum Error.
F020	Memory Checksum Error.
F030	Main PWB System Error.
F040	Engine PWB Communication Error.
F041	Scanner PWB Communication Error.
F050	Engine ROM Checksum Error.
F060	Engine RAM Error.
F070	Flash ROM Error.
F080	Flash ROM Error (during download).
F090	Fax Control PWB Communication Error.
F14F	Power Source PWB Second Side Error.
E00000 or U00000	Fax Communication Error: No response or line busy after the set number of redials.
E00100 or U00100	Fax Communication Error: Transmission was interruped by a press of the Stop/Clear key.
E00200 or U00200	Fax Communication Error: Reception was interrupted by a press of the Stop/Clear key.
E00300 or U00300	Fax Communication Error: Recording paper on the destination unit has run out during reception.
E00420 or U00420	Fax Communication Error: A relay request was received from the host center but interrupted because of a mismatch in permit ID or telephone number.
E00421 or U00421	Fax Communication Error: Subaddress-based relay reception was interrupted because of a mismatch in the specified subaddress relay box number.
E00430 or U00430	Fax Communication Error: Polling request (confidential or reverse polling) was received but interrupted because of a mismatch in the permit number.
E00430 or U00430	Fax Communication Error: Subaddress-based bulletin board transmission was interrupted because of a mismatch in the permit ID of the transmitting unit.
E00431 or U00431	Fax Communication Error: Confidential polling transmission was interrupted because the specified confidential box number was not registered.
E00431 or U00431	Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because the specified subaddress confidential box was not registered.
E00432 or U00432	Fax Communication Error: Confidential polling transmission was interrupted because of a mismatch in the confidential box ID number.
E00432 or U00432	Fax Communication Error: A subaddress-based bulletin board transmission was interrupted because of a mismatch in the subaddress confidential box number.
E00433 or U00433	Fax Communication Error: Confidential polling request was received but data was not present in the confidential box.
E00433 or U00433	Fax Communication Error: Subaddress-based bulletin board transmission request was received but data was not present in the subaddress confidential box.
E00434 or U00434	Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box number was intended for encryption.
E00435 or U00435	Fax Communication Error: Confidential polling request was received but interrupted because the specified confidential box was being accessed.
E00435 or U00435	Fax Communication Error: Subaddress-based bulletin board transmission request was received but interrupted because the specific subaddress confidential box was being accessed.
E00440 or U00440	Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was not registered.
E00440 or U00440	Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay reception was interrupted because the specific subaddress box was not registered.
E00440 or U00440	Fax Communication Error: Subaddress-based confidential reception or subaddress-based relay command reception was interrupted because the specific subaddress box number was being accessed.
E00441 or U00441	Fax Communication Error: Confidential reception was interrupted because the specified confidential box number was intended for encryption.
E00450 or U00450	Fax Communication Error: The destination transmitter disconnected because the permit IDs did not agree while the destination transitter is in password-check transmission or restricted transmission.
E00460 or U00460	Fax Communication Error: Encrypted reception was interrupted because the specified encryption box number was not registered.
E00460 or U00460	Fax Communication Error: Ecrypted reception request was received but interrupted because the specified encryption box was being accessed.
E00462 or U00462	Fax Communication Error: Ecryption reception was interrupted because the encryption key for the specified encryption box was not registered.
E00500 or U00500	Fax Communication Error: Multiple communication was interrupted and the call was not made on destination units after interruption.
E00600 or U00600	Fax Communication Error: The document processor cover is open.
E00601 or U00601	Fax Communication Error: Document jam or the document length exceeds the maximum.
E00602 or U00602	Fax Communication Error: Image scanning section problem
E00603 or U00603	Fax Communication Error: No document feed.
E00604 or U00604	Fax Communication Error: Document length exceeded the limit of the bitmap memory capacity.
E00610 or U00610	Fax Communication Error: Recording section cover open.
E00611 or U00611	Fax Communication Error: Recording paper jam.
E00613 or U00613	Fax Communication Error: Image writing section problem.
E00614 or U00614	Fax Communication Error: Nearly empty of recording paper.
E00615 or U00615	Fax Communication Error: Empty of recording paper.
E00620 or U00620	Fax Communication Error: Copier fixing unit problem.
E00622 or U00622	Fax Communication Error: Copier drive motor problem.
E00655 or U00655	Fax Communication Error: CTS was not activated after RTS due to a modem error.
E00656 or U00656	Fax Communication Error: Data was not transmitted after CTS was activated due to a modem error.
E00670 or U00670	Fax Communication Error: Power was cut off during communication.
E00677 or U00677	Fax Communication Error: There was no file to transmit in the memory transmission mode.
E00690 or U00690	Fax Communication Error: System error.
E00700 or U00700	Fax Communication Error: Communication was interrupted because of a problem in the destination unit.
E00800 or U00800	Fax Communication Error: A page transmission error occurred in G3 mode, because of reception of a RTN or PIN signal.
E00810 or U00810	Fax Communication Error: A page transmission error re-occurred in G3 mode after retry of transmission in ECM mode.
E00900 or U00900	Fax Communication Error: A page reception error occurred in G3 mode. An RTN or PIN signal was transmitted because of a page reception error.
E00910 or U00910	Fax Communication Error: A page reception error occurred in G3 mode. A page reception error remained after retry of transmission in ECM mode.
E01000 or U01000	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An FTT signal was received for a set number of times after TCF signal transmissions at 2400bps.
E01000 or U01000	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400bps.
E01001 or U01001	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. The function of the unit differs from that indicated by a DIS signal.
E01010 or U01010	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01011 or U01011	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded.
E01012 or U01012	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make).
E01013 or U01013	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make).
E01014 or U01014	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded.
E01015 or U01015	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded.
E01016 or U01016	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected.
E01017 or U01017	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded.
E01018 or U01018	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded.
E01019 or U01019	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make).
E01020 or U01020	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM).
E01021 or U01021	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM).
E01022 or U01022	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a RR signal, and the preset number of command retransfers was exceeded (ECM).
E01023 or U01023	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PS.NULL signal, and the preset number of command retransfers was exceeded (ECM).
E01024 or U01024	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.MPS signal, and the preset number of command retransfers was exceeded (ECM).
E01025 or U01025	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM).
E01026 or U01026	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01027 or U01027	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM).
E01028 or U01028	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. T5 timeout was detected during ECM Transmission (ECM).
E01040 or U01040	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received during standby for DIS signal reception.
E01041 or U01041	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make).
E01042 or U01042	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS, TCF signal.
E01043 or U01043	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS1, NSS2 (TCF) signal (between units of our make).
E01044 or U01044	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an NSS3, TCF signal (between units of our make).
E01045 or U01045	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an MPS signal.
E01046 or U01046	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOM signal.
E01047 or U01047	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN or other inappropriate signal was received after transmission of an EOP signal.
E01048 or U01048	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PRI-EOP signal.
E01049 or U01049	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CNC signal (between units of our make).
E01050 or U01050	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTC signal (ECM).
E01051 or U01051	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an EOR.Q signal (ECM).
E01052 or U01052	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RR signal (ECM).
E01053 or U01053	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.NULL signal (ECM).
E01054 or U01054	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.MPS signal (ECM).
E01055 or U01055	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOM signal (ECM).
E01056 or U01056	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.EOP signal (ECM).
E01057 or U01057	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPS.PRI-EOP signal (ECM).
E01070 or U01070	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during handshake.
E01071 or U01071	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. Polarity reversal was detected during message transmission.
E01072 or U01072	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A break in loop current was detected during transmission.
E01073 or U01073	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the receiver unit, a CM signal was not detected when transmitting after reception.
E01080 or U01080	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. A PIP signal was received after transmission of a PPS.NULL signal.
E01091 or U01091	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because a PPR signal was received over (10) times even after reducing the communication speed to the minimum with the symbol speed maintained at the level of connection.
E01092 or U01092	Fax Communication Error: Transmission in G3 mode was interrupted by a signal error. During transmission in V.34 mode, communication was interrupted because of an impossible combination of the symbol speed and communication speed.
E01100 or U01100	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit differs from that indicated by a DCS signal.
E01101 or U01101	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Function of the unit (excl. communication mode select) differs from that indicated by an NSS signal.
E01102 or U01102	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DTC (NSC) signal was received when no transmission data was in the unit.
E01110 or U01110	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DIS signal.
E01111 or U01111	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a DTC (NSC) signal.
E01112 or U01112	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No training reception after reception of a DCS or NSS signal.
E01113 or U01113	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an FTT signal.
E01114 or U01114	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CFR signal.
E01115 or U01115	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an MCF signal.
E01116 or U01116	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a PPR signal.
E01117 or U01117	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of a CTR signal.
E01118 or U01118	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No message reception after transmission of an ERR signal.
E01119 or U01119	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No further signals were received after reception of a message.
E01120 or U01120	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an MCF signal.
E01121 or U01121	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTP signal.
E01122 or U01122	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RTN signal.
E01123 or U01123	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIP signal.
E01124 or U01124	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PIN signal.
E01125 or U01125	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a CNS signal (between units of our make).
E01126 or U01126	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of a PPR signal (ECM).
E01127 or U01127	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an ERR signal (ECM).
E01128 or U01128	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an RNR signal (ECM).
E01129 or U01129	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. No response after transmission of an SPA signal (short protocol).
E01140 or U01140	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DIS signal.
E01141 or U01141	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DTC signal.
E01142 or U01142	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a DCS or NSS signal.
E01143 or U01143	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an FTT signal.
E01144 or U01144	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CFR signal.
E01145 or U01145	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after reception of a message.
E01146 or U01146	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an MCF signal (interoffice communication after reception of an MPS, EOM signal or confidential interoffice communication).
E01147 or U01147	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTP signal.
E01148 or U01148	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an RTN signal.
E01149 or U01149	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIPsignal.
E01150 or U01150	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PIN signal.
E01151 or U01151	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a PPR signal (ECM).
E01152 or U01152	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of a CTR signal (ECM).
E01153 or U01153	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an ERR signal (ECM).
E01154 or U01154	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an PNP signal (ECM).
E01155 or U01155	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DCN signal was received after transmission of an SPA signal (short protocol).
E01160 or U01160	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During message reception, transmission time exceeded the maximum transmission time per line.
E01161 or U01161	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Number of error lines exceeded limits during message reception.
E01162 or U01162	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A break in loop current was detected during message reception.
E01163 or U01163	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Polarity reversal was detected during message reception.
E01164 or U01164	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. One page length exceeded the specified length during message reception.
E01170 or U01170	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A decoding error occurred during MMR message reception.
E01172 or U01172	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. During reverse polling in V.34 mode at the transmitting unit, a JM signal was not detected after transmission of a CM signal when receiving after transmission.
E01191 or U01191	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. Communication was interrupted because an error occurred during an image data reception sequence in the V.34 mode.
E01199 or U01199	Fax Communication Error: Reception in G3 mode was interrupted by a signal error. A DIS signal with different FIF was received after transmission of a DIS signal.
E01400 or U01400	Fax Communication Error: An invalid one-touch key was specified during communication.
E01500 or U01500	Fax Communication Error: A communication error occurred when calling in V.8 mode.
E01600 or U01600	Fax Communication Error: A communication error occurred when called in V.8 mode.
E01700 or U01700	Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol, during transmission in V.34 mode. For example: INFO0/A/Abar (B/Bbar, for polling transmission)/INFOh was not detected.
E01720 or U01720	Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol, during transmission in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E01721 or U01721	Fax Communication Error: A communication error occurred before starting T.30 protocol during transmission in V.34 mode. Operation was interrupted due to the absence of a common communication speed between the units. 1) A DCN signal was received from the destination unit and the line was cut, or 2) a DIS (NSF, CSI) signal was received from the destination unit and in response to the signal, the unit transmitted a DCN signal and the line was cut.
E01800 or U01800	Fax Communication Error: A communication error occurred in phase 2 (line probing) in the period after transmission of INFO0, before entering phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: INFO0/B/Bbar (A/Abar, for polling reception)/probing tone was not detected.
E01810 or U01810	Fax Communication Error: A communication error occurred in phase 3 (primary channel equivalent device training), before starting T.30 protocol during reception in V.34 mode. For example: S/Sbar/PP/TRN was not detected.
E01820 or U01820	Fax Communication Error: A communication error occurred in phase 4 (modem parameter exchange) in the period after initiating the control channel, before starting T.30 protocol during reception in V.34 mode. For example: PPh/ALT/MPh/E was not detected.
E02000 or U02000	Fax Communication Error: Relay broadcast was refused by a relay station because of a mismatch in permit ID number and permit telephone number when a relay command was used.
E02100 or U02100	Fax Communication Error: A relay command failed because the destination unit (relay station) had no relay broadcast capability.
E02200 or U02200	Fax Communication Error: A relay command from a command station failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200	Fax Communication Error: Relay broadcast was requested to a relay station but failed because a telephone number was not registered in the relay station was specified.
E02200 or U02200	Fax Communication Error: Subaddress-based relay broadcast transmission failed because the data registered in the subaddress relay box was deleted.
E02303 or U02303	Fax Communication Error: Receiving station information was not normally received in reception of a relay command. Timeout was detected before a correct DNL signal was received.
E02304 or U02304	Fax Communication Error: Receiving station information was not normally received in reception of a relay command. A signal other than MPS or EOM signal was received after a DNL signal was received.
E02400 or U02400	Fax Communication Error: An interoffice subaddress-based relay transmission was interrupted because of a mismatch in the specified relay box number.
E03000 or U03000	Fax Communication Error: No document was present in the destination unit when polling reception started.
E03100 or U03100	Fax Communication Error: In reverse polling, although no original was set in the destination unit, transmission was complete.
E03200 or U03200	Fax Communication Error: In confidential polling reception, data was not accumulated in the specified box in the destination unit.
E03200 or U03200	Fax Communication Error: In interoffice subaddress-based bulletin board reception, data was not stored in the box specified by the destination unit.
E03300 or U03300	Fax Communication Error: In polling reception from a unit of our make, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03300 or U03300	Fax Communication Error: In interoffice subaddress-based bulletin board reception, operation was interrupted due to a mismatch in permit ID number or telephone number.
E03400 or U03400	Fax Communication Error: Polling reception was interupted because of a mismatch in individual numbers.
E03500 or U03500	Fax Communication Error: In confidential polling reception, the specified confidential box number was not registered in the destination.
E03500 or U03500	Fax Communication Error: In interoffice subaddress-based bulletin board reception, the specified subaddress confidential box number was not registered in the destination unit.
E03500 or U03500	Fax Communication Error: The destination was being accessed.
E03600 or U03600	Fax Communication Error: Confidential polling reception was interrupted because of a mismatch in specified confidential box numbers.
E03600 or U03600	Fax Communication Error: An interoffice subaddress-based bulletin board reception was interrupted because of a mismatch in the specified subaddress confidential box number.
E03700 or U03700	Fax Communication Error: Confidential polling reception failed because the destination unit had no confidential polling transmission capability or data was not accumulated in any box in the destination unit.
E03700 or U03700	Fax Communication Error: Interoffice subaddress-based bulletin board reception failed because the destination unit had no subaddress-based bulletin board transmission capability, or data was not stored in any subaddress confidental box in the destination unit.
E04000 or U04000	Fax Communication Error: The confidential box specified for confidential transmission was not registered in the destination unit.
E04000 or U04000	Fax Communication Error: In interoffice subaddress-based transmission mode, the specified subaddress box number was not registered in the destination unit.
E04000 or U04000	Fax Communication Error: The destination was being accessed.
E04100 or U04100	Fax Communication Error: Confidential transmission failed because the destination unit had no confidential capability.
E04100 or U04100	Fax Communication Error: Subaddress-based transmission failed because the destination unit had no subaddress-based reception capability.
E04200 or U04200	Fax Communication Error: In encrypted tranmission, the specified encryption box was not registered in the destination unit.
E04300 or U04300	Fax Communication Error: Encrypted transmission failed because the destination unit had no encrypted communication capability.
E04400 or U04400	Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted transmission. Encryption keys did not agree.
E04401 or U04401	Fax Communication Error: Communication was interrupted because of an encryption key error during encrypted trasmission. The encryption key was not registered.
E04500 or U04500	Fax Communication Error: Encrypted reception was interrupted because of a mismatch in ecryption keys.
E05000 or U05000	Fax Communication Error: In transmission with a specified number, the set number of originals was different from the number of transmitted originals.
E05100 or U05100	Fax Communication Error: Password check transmission or restricted transmission was interrupted because the permit ID numbers did not match.
E05200 or U05200	Fax Communication Error: Password check reception or restricted reception was interrupted because the permit ID numbers did not match, the rejected fax numbers did match, or the destination receiver did not return its phone number.
E05300 or U05300	Fax Communication Error: Password check reception or restricted reception was interrupted because the permitted numbers did not match, the rejected numbers did match, or the machine in question did not acknowledge its phone number.
E09000 or U09000	Fax Communication Error: G3 communication was attempted but failed because the destination unit was a G2 machine.
E12000 or U12000	Fax Communication Error: Relay broadcast was requested from a command station but memory overflowed during reception.
E12000 or U12000	Fax Communication Error: In subaddress-based relay reception memory overflowed.
E12100 or U12100	Fax Communication Error: Relay was commanded but memory overflowed in the destination unit (relay station).
E14000 or U14000	Fax Communication Error: Memory overflowed during confidential reception.
E14000 or U14000	Fax Communication Error: Memory overflowed in subaddress-based confidential reception.
E14100 or U14100	Fax Communication Error: Memory overflowed in the destination unit during confidential transmission.
E14100 or U14100	Fax Communication Error: Memory overflowed in the destination unit during interoffice subaddress-based transmission.
E19000 or U19000	Fax Communication Error: Memory overflowed during memory reception.
E19100 or U19100	Fax Communication Error: Memory overflowed in the destination unit during transmission.
E19200 or U19200	Fax Communication Error: Memory transmission failed because a decoding error occurred.
E19300 or U19300	Fax Communication Error: Transmission failed because an error occurred during JBIG encoding.
E19400 or U19400	Fax Communication Error: Reception failed because an error occurred during JBIG encoding.
Send SMB Error 1102	Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send SMB Error 1102	Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send SMB Error 1102	Error: Username/Password or Shared Name/Folder Name. Assign the user who is not allowed to access the folder.
Send SMB Error 1102	Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send SMB Error 1102	Error: Username/Password or Shared Name/Folder Name. Host name error.
Send SMB Error 1103	Error: Pathname or File Name. Domain name is not entered.
Send SMB Error 1103	Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send SMB Error 1103	Error: Pathname or File Name. Assign disable folder path.
Send SMB Error 1105	Error: Not Supported Protocol. SMB protocol is set to OFF.
Send SMB Error 2101	Error: Can Not Connect. Enter the disable host name/IP address.
Send SMB Error 2101	Error: Can Not Connect. Assign the wrong port number.
Send SMB Error 2101	Error: Can Not Connect. Network is not connected.
Send SMB Error 2103	Error: Response Wait With Timeout. The server is unable to communicate.
Send SMB Error 2201	Error: Network Transfer. Error occurs on the network.
Send SMB Error 2203	Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send SMB Error 9181	Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send FTP Error 1101	Error: Host Name. Enter the disable host name/IP address.
Send FTP Error 1102	Error: Username/Password. Domain name is not entered.
Send FTP Error 1102	Error: Username/Password. Assign disable user/password.
Send FTP Error 1103	Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send FTP Error 1103	Error: Pathname or File Name. Assign disable folder path.
Send FTP Error 1105	Error: Not Supported Protocol. FTP protocol is set to OFF.
Send FTP Error 2101	Error: Can Not Connect. Enter the disable host name/IP address.
Send FTP Error 2101	Error: Can Not Connect. Assign the wrong port number.
Send FTP Error 2101	Error: Can Not Connect. Network is not connected.
Send FTP Error 2102	Error: Cannot Connect With Timeout. The server is unable to communicate.
Send FTP Error 2102	Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send FTP Error 2103	Error: Response Wait With Timeout. The server is unable to communicate.
Send FTP Error 2201	Error: Network Transfer. Error occurs on the network.
Send FTP Error 2202	Error: Network Transfer With Timeout. Error occurs on the network.
Send FTP Error 2203	Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send FTP Error 3101	Error: Server Response. The server is error status.
Send FTP Error 9181	Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Send email Error 1101	Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send email Error 1102	Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send email Error 1104	Error: No Recipient Address. The destination address is not specified.
Send email Error 1105	Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send email Error 1106	Error: No Sender Info. Sender address is not entered.
Send email Error 2101	Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send email Error 2101	Error: Can Not Connect. The specified server is not SMTP server.
Send email Error 2101	Error: Can Not Connect. Network is not connected.
Send email Error 2102	Error: Cannot Connect With Timeout. The server is unable to communicate.
Send email Error 2103	Error: Response Wait With Timeout. The server is unable to communicate.
Send email Error 2201	Error: Network Transfer. Error occurs on the network.
Send email Error 2202	Error: Network Transfer With Timeout. Error occurs on the network.
Send email Error 2203	Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send email Error 2204	Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send email Error 3101	Error: Server Response. The server is error status.
Send email Error 3101	Error: Server Response. Server setting is not authenticated normally.
Send email Error 3201	Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send email Error 9181	Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
TWAIN Error 2202	Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
TWAIN Error 9181	Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
Software Error 5101	Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5102	Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Software Error 5103	Error: Not Yet Opened. Error for storage status in the operation handle.
Software Error 5104	Error: Already Opened. Error for storage status in the operation handle.
Software Error 7101	Error: Memory Allocation. Insufficient memory space.
Software Error 7102	Error: Socket Create. Unable to create a communication socket.
Software Error 720f	Error: Unknown Error. Unable to determine the cause.
Send error. Job is cancelled. Press [End]. 1101	Send Email Error: Host Name. SMTP server name is not set. Error SMTP server name.
Send error. Job is cancelled. Press [End]. 1101	Send FTP Error: Host Name. Enter the disable host name/IP address.
Send error. Job is cancelled. Press [End]. 1102	Send Email Error: Username/Password. User ID for the authentication is not entered or entered wrongly. Wrong authentication password is entered.
Send error. Job is cancelled. Press [End]. 1102	Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Domain name is not entered.
Send error. Job is cancelled. Press [End]. 1102	Send SMB/FTP Error: Username/Password or Shared Name/Folder Name. Assign disable user/password.
Send error. Job is cancelled. Press [End]. 1102	Send SMB Error: Username/Password or Shared Name/Folder Name. Assign disable shared name.
Send error. Job is cancelled. Press [End]. 1102	Send SMB Error: Username/Password or Shared Name/Folder Name. Host name error.
Send error. Job is cancelled. Press [End]. 1103	Send SMB/FTP Error: Pathname or File Name. Domain name is not entered.
Send error. Job is cancelled. Press [End]. 1103	Send SMB/FTP Error: Pathname or File Name. Connect to the folder which is not permitted for reference/writing.
Send error. Job is cancelled. Press [End]. 1103	Send SMB/FTP Error: Pathname or File Name. Assign disable folder path.
Send error. Job is cancelled. Press [End]. 1104	Send Email Error: No Recipient Address. The destination address is not specified.
Send error. Job is cancelled. Press [End]. 1105	Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1105	Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1105	Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
Send error. Job is cancelled. Press [End]. 1106	Send Email Error: No Sender Info. Sender address is not entered.
Send error. Job is cancelled. Press [End]. 2101	Send Email Error: Can Not Connect. Network is not connected.
Send error. Job is cancelled. Press [End]. 2101	Send Email Error: Can Not Connect. Select [Other Authenticate] when authenticating POP before SMTP.
Send error. Job is cancelled. Press [End]. 2101	Send Email Error: Can Not Connect. The specified server is not SMTP server.
Send error. Job is cancelled. Press [End]. 2101	Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP address.
Send error. Job is cancelled. Press [End]. 2101	Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
Send error. Job is cancelled. Press [End]. 2101	Send SMB/FTP Error: Can Not Connect. Network is not connected.
Send error. Job is cancelled. Press [End]. 2102	Send Email/ FTP Error: Cannot Connect With Timeout. The server is unable to communicate.
Send error. Job is cancelled. Press [End]. 2102	Send FTP Error: Cannot Connect With Timeout. Send the server which does not support FTP server.
Send error. Job is cancelled. Press [End]. 2103	Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server is unable to communicate.
Send error. Job is cancelled. Press [End]. 2201	Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the network.
Send error. Job is cancelled. Press [End]. 2202	Send Email/FTP Error: Network Transfer With Timeout. Error occurs on the network.
Send error. Job is cancelled. Press [End]. 2202	Send TWAIN Error: Network Transfer With Timeout. Response is not returned from the server, above the specified time.
Send error. Job is cancelled. Press [End]. 2203	Send Email/FTP Error: Response Wait With Timeout. Response is not returned from the server, above specified time.
Send error. Job is cancelled. Press [End]. 2204	Send Email Error: Email Size Limit. The size of the email attachment exceeds its limit.
Send error. Job is cancelled. Press [End]. 3101	Send Email/FTP Error: Server Response. The server is error status.
Send error. Job is cancelled. Press [End]. 3101	Send Email Error: Server Response. Server setting is not authenticated normally.
Send error. Job is cancelled. Press [End]. 3201	Send Email Error: Not Found Authentication Mechanism. Unsupported SMTP Authentication Mechanism is found.
Send error. Job is cancelled. Press [End]. 5101	Send Software Error: Not Yet Connected. Operation handle error. Error for stored status in the operation handle.
Send error. Job is cancelled. Press [End]. 5102	Send Software Error: Already Connected. Operation handle error. Error for stored status in the operation handle.
Send error. Job is cancelled. Press [End]. 5103	Send SoftwareError: Not Yet Opened. Error for storage status in the operation handle.
Send error. Job is cancelled. Press [End]. 5104	Send Software Error: Already Opened. Error for storage status in the operation handle.
Send error. Job is cancelled. Press [End]. 7102	Send Software Error: Socket Create. Unable to create a communication socket.
Send error. Job is cancelled. Press [End]. 720f	Send Software Error: Unknown Error. Unable to determine the cause.
Send error. Job is cancelled. Press [End]. 9181	Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The number of pages of a send file exceeds 999 pages.
"Acceptable staple count exceeded."	Is the acceptable staple count exceeded?
"Add paper in cassette #."	Is the indicated cassette out of paper?
"Add paper in MP tray."	Is the paper of the specified size loaded in the multipurpose tray?
"Add staples."	Has the document finisher run out of staples?
"Add toner."
"An error has occurred."	An internal error has occurred.Make a note of the error code number displayed on the panel. See above.
"Box Limit Exceeded."	Document Box is full, and no further storage is available; Job is cancelled. Repeat Copy Box is full, and no further repeat copy is available.
"Cannot connect to Authentication Server."
"Cannot duplex print on this paper."	Did you select a paper size/type that cannot be duplex printed?
"Cannot execute this job."	Job is restricted by Job Accounting.
"Cannot offset this paper."	Did you select a paper size that cannot be offset (A3, B4, A5R, B6R, Folio, Ledger, Statement, & 8K)?
"Cannot punch this paper type."	Did you select a paper size/type that cannot be punched?
"Cannot staple this paper."	Did you select a paper size/type that cannot be stapled?
"Check the cover."	Are any covers open? Does the message indicate which cover is open?
"Check the document processor."	Is the document processor open? Is the top cover of the document processor open?
"Check the finisher."	Is the document finisher set correctly?"
"Clean the slit glass."	Dirt has been identified on the slit glass.
"Empty the punch waste box."	The punch waste box of the 3,000 sheet finisher is full.
"Failed to specify Job Accounting."	Job accounting is not specified in the print driver.
"Failed to store job retention data."
"Fax box limit exceeded."	Fax box is full, and no further storage is available.
"Finisher tray is full of paper."	Is the acceptable storage capacity exceeded for the document finisher tray?"
"Folding tray is full of paper."	Is the acceptable storage capacity exceeded for the folding tray of the 3,000 sheet document finisher?"
"Hard Disk error. Job is cancelled. Press [End] ##"	An error has occurred on the hard disk.
"Incorrect Login User Name or Password."
"Job Accounting restriction exceeded."	The print count exceeded the acceptable count restricted by Job Accounting.
"Job Separator is full of paper."	Is the maximum capacity of the job separator tray exceeded?
"KPDL error."	A PostScript error has occurred.
"Mailbox tray is full of paper."
"Memory card error."	Was the memory card (Compact Flash) removed while being accessed? Was a valid memory card inserted?
"Memory card error. Job is cancelled. Press [End]. Code: 01	Memory Card Error: Format error.
"Memory card error. Job is cancelled. Press [End]. Code: 04	Memory Card Error: Insufficient memory card space to complete this operation.
"Memory is full."	Unable to continue the job, as the memory is used up."
"Memory Is Low"	Logic Lockup
"Paper Jam. ###"	Make a note of the jam location number displayed on the panel. Leave the machine On.
"Print overrun."	Warning. Low printer memory.
"Removable memory error."	An error has occurred on the USB stick memory or Compact Flash memory.
"Removable memory was removed."
"Replace all originals and press [Continue]."
"Replace the waste toner box."	The waste toner box is full.
"Reset all originals in the document processor."	Are there any originals left in the document processor?
"Scanner memory is full."	Scanning cannot be performed due to insufficient memory for the scanner. Is the acceptable scanning count exceeded?
"Scanner Paused"	DMA transmission of compressed, ecompressed, rotated, relocated, or blanked-out image data does not complete within a specified period of time.
"Set the folding tray."	Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
"Set the folding unit."	Is the folding tray correctly installed to the 3,000 sheet capacity document finisher?
"Set the punch waste box."	The waste toner box is not installed correctly.
"Set the waste toner box."	The waste toner box is not installed correctly.
"Staple error."	The location of the jam will be indicated on the panel. Leave the machine On.
"Staple jam."	The location of the jam will be indicated on the panel. Leave the machine On.
"The ID is not registered."	The account ID# does not match.
"The memory card is not formatted."	Is the removable memory formatted by this machine?
"The phone receiver is off the hook."
"The removable memory is not formatted."	Is the removable memory formatted by this machine?
"The source file is not found."	The specified file is not found.
"Top tray of the machine is full of paper."	The exit tray at the top of the machine is full.
"Tray # is full of paper."	Is the acceptable storage capacity exceeded for any of the output trays A, B, or C of the 3,000 sheet capacity document finisher?
"Warning low memory."	Further scanning cannot be performed due to insufficient memory.

Error Code	Description
0xF330	Component: RIP. Category: RIP. Recovery impossible error (CreatePrint and return back value of API is indirect).
0xF331	Component: RIP. Category: RIP. Fail to initialize.
0xF333	Component: RIP. Category: RIP. Access failure to ME.
0xF335	Component: RIP. Category: RIP. Failure to switch TASK.
0xF336	Component: RIP. Category: RIP. IOBL process failure.
0xFB30	Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
0xFB31	Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
0xFB32	Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
0xFB33	Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected - waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
0xFB34	Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
0xFB35	Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
0xFB36	Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
0xFB37	Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
0xFB38	Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
0xFB39	Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
0xFB3A	Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).
CF000	Component: HDD. Failure to initialize with "dbinit, hostif_stat_chg" comand.
CF000	Operation panel PWB comunication error.
CF010	ROM Checksum Error.
CF010	Main PWB Checksum Error/System Error. Communication error between panel and main controller.
CF012	ROM Checksum Error.
CF020	Memory Checksum Error/Operation System Error.
CF030	Main PWB System Error.
CF040	Engine PWB Communication Error.
CF040	Engine PWB Communication Error.
CF041	Scanner PWB Communication Error.
CF050	Engine ROM Checksum Error.
CF060	Engine RAM Error.
CF070	Flash ROM Error. Defective flash ROM (which?).
CF080	Flash ROM Error (during download). Defective flash ROM (which?).
CF090	Fax System M Communication Error.
CF125	Scanner Unit Error
CF131	Component: PCM. Category: OS. Failure to initialize with "dbinit, hostif_stat_chg" comand.
CF131	Component: PCM. Category: OS. Failure to acquire Entity data with "dbinit, hostif_stat_chg" comand.
CF145	Fax Unit Error.
CF14F	Power Source Secondary Side Error/Operation System Error. The operation decomes unstable after recovering the power supply fail (brownout or power drop). Wall voltage is unstable or the main power supply switch was turned OFF/ON within 1 sec.
CF14F	Component: OS. Category: OS. Primary supply voltage dropped off temporarily and recovery operation was not stable. If the input power supply voltage is not stable of the Main SW is turned Off/On quickly (about 1 second), this problem occurs.
CF186	Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data flushing error)
CF18A	Engine Firmware Incompatible.
CF18C	Document BOX error.
CF1FF	Component: ScanSys. Category: ScanSys. When the scanner scanning parameter from the topside is in error.
CF1FF	Component: IPLogical. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: ipl_search_output.cpp, ipl_feeder_spec.cpp, outputcheck.cpp.
CF1FF	Component: Machine Configuration. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: machine_status_engine.cpp.
CF1FF	Component: OutputMission. Category: PrintSystem. Increasing and decreasing "Lib", in case that even if there is no original available, tried to process increasing & decreasing.
CF1FF	Component: OutputMission. Category: PrintSystem. In case to specify some other value (indirect value) other than single sided/duplex/forced duplex for increasing & decreasing "Lib".
CF1FF	Component: OutputMission. Category: PrintSystem. In case of the address for Job setting value structure is NULL.
CF1FF	Component: OutputMission. Category: PrintSystem. In case of the code for output completion notice is indirect.
CF1FF	Component: OutputMission. Category: PrintSystem. When writing the original information to the storage, in case to get the reply back as [Other Error].
CF1FF	Component: OutputMission. Category: PrintSystem. In case to get the reply as [Finisher out of order Error], [No Feeder available in search] from Paper feed/eject "Lib".
CF1FF	Component: OutputMission. Category: PrintSystem. In case to get the reply as failure from rotation calculation "Lib".
CF1FF	Component: PrintSystem. Category: PrintSystem. Could not obtain instance of Config, SystemStatus. Use below mentioned class: print_startup.cpp.
CF1FF	Component: SVI. Category: LioPanel. Logical Error (In case of given parameter is NULL).
CF214	Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware error, software error).
CF215	Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware error, software error).
CF234	Data conversion error.
CF235	Error code when receiving/printing email.
CF245	Process Manager: SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device process down).
CF246	Process Manager: SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device process down).
CF247	Process Manager: SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image process down).
CF247	Component: ScanSys. Category: ScanSys. Library Error inside of ScanSys.
CF248	Component: UNKNOWN. Category: UNKNOWN.
CF248	Component: UNKNOWN. Category: UNKNOWN. Code present on with Kyocera Barfode Font CF card installed.
CF248	Process Manager: SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer process down).
CF256	Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257	Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF257	Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card due to mis-installation.
CF25E	Network Manager:
CF25F	Component: LFM. Category: FaxSys. Instance Check Error, Paramemter Error from topside.
CF26F	Component: PrintSys. Category: PrintSys. It occurs when the error noticed from VideoDriver. Use by Video_Driver class: Function name, factor can be found by the detail code.
CF26F	Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet > Booklet Print).
CF26F	System State Manager:
CF278	Energy Saving Manager:
CF320	Component: LioFax. Category: FaxSys. An Observer Deletion Error occurred during salvage process. Error received from the method on EventManager or message Tx.
CF321	Component: LioFax. Category: FaxSys. Segment code for LioFax initialization is different from "03KH".
CF323	Component: LioFax. Category: FaxSys. Return address of Page class when doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access error.
CF324	Component: LioFax. Category: FaxSys. Entity parameter error.
CF325	Component: LioFax. Category: FaxSys. In case that the time when Error came back from LFM.
CF326	Component: LioFax. Category: FaxSys. IOBL error.
CF327	Component: LioFax. Category: FaxSys. At the time of KUIOLIB error, CodeChange error, FaxLib error (Sender recorde, Entity related error).
CF32F	Component: LioFax. Category: FaxSys. Instance Check Error. Parameter Error from topside.
CF337	Device Error (scan control):
CF3FF	Component: RIP. Category: RIP. Other/System Crucial Error.
CF423	Component: FaxJOB. Category: FaxSys. As the error came back at IF for DocumentBox, JobInfo, Config Entity.
CF423	Component: FaxJob. Category: FaxSys. The error came back when accessing (obtaining data, setting data) to below Entity related: job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate), document_box.
CF423	Fax System M Error. Wrong data or value detected when the following function is used. Or poor contact at fax card due to mis-installation.
CF423	Fax System M Error. The IF error detects during system authentication from ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CF424	Component: FaxJob. Category: FaxSys. As the error came back when obtaining IF for system authentication from ACT_Account_Manager.
CF424	Component: FaxJob. Category: FaxSys. The date obtained from the below Entity related is unexpected data: job_ent(JobInfo).
CF427	Component: FaxJob. Category: FaxSys. The error came back for the IF of LioFax observer addition/deletion.
CF42F	Component: FaxJob. Category: FaxSys. As handing over of the NULL pointer in the class occurred. As memory reservation with new in heap domain is failed: Assert for preventing from segment drop off.
CF42F	Component: FaxJob. Category: FaxSys. When generating the class, fail new at obtaining data domain, soft logic error (software bug).
CF433	Component: NetClient. Category: ImageProcess. Entity Error.
CF434	Component: NetClient. Category: ImageProcess. Entity Data Invalid.
CF437	Component: NetClient. Category: ImageProcess. Other Library Error (ImageLibrary, PageData, EventManager).
CF43F	Component: NetClient. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF441	Component: CreateScan. Category: ImageProcess. Initialize Error.
CF444	Component: CreateScan. Category: ImageProcess. Entity Data Invalid.
CF445	Component: CreateScan. Category: ImageProcess. Middleware Error (LioScanner error).
CF451	Component: CreatePrint. Category: ImageProcess. Initialization Error.
CF433 CF434 CF437 CF43F CF441 CF444 CF445 CF451	HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF453	Component: CreatePrint. Category: ImageProcess. Entity Error.
CF454	Component: CreatePrint. Category: ImageProcess. Entity Data Mismatch.
CF45F	Component: CreatePrint. Category: ImageProcess. Other Error.
CF460	Component: CreateBox (Memory Tx). Category: ImageProcess. Unrecoverable Error.
CF463	Component: CreateBox (Memory Tx). Category: ImageProcess. Entity Error.
CF46F	Component: CreateBox (Memory Tx). Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF46F	PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other general error).
CF470	Component: CreateFax. Category: ImageProcess. Unrecoverable Error.
CF473	Component: CreateFax. Category: ImageProcess. Entity Error.
CF47F	Component: CreateFax. Category: ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF484	Component: Edit. Category: ImageProcess. Data Invalid (PageData).
CF487	Component: Edit. Category: ImageProcess. Other Library Error (ImageLibrary).
CF48F	Component: Edit. Category: ImageProcess. Crucial.
CF490	Component: Output(Fax). Category: ImageProcess. Unrecoverable Error.
CF493	Component: Output(Fax). Category: ImageProcess. Entity Error.
CF494	Component: Output(Fax). Category: ImageProcess. Entity Data Invalid.
CF45F CF453 CF454 CF45F CF460 CF463 CF46F CF470 CF473 CF47F CF484 CF487 CF48F CF490 CF493 CF494	HDD Image Process Error. Destruction of stored jobs on the HDD. It may occur when selecting the keys for calling stored copy or scanner job from a custom box.
CF515
CF526	System Error:
CF528	Component: SVI. Category: LioPanel. Panel data abusion error.
CF530	Component: PJL. Category: RIP. Recovery impossible error: Thread Create failed.
CF530	Component: ReportEventService. Category: RIP. Recovery impossible error: Thread Create failed.
CF530	Component: SVCTL_FaxRx_Event_Control. Category: KI Sc. As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.
CF530	Component: SVCTL_Reservation_Event_Control. Category: KI Sc. As failed to notice the event for EM_Rsv_EC_op_Event_FaxJob_Ready.
CF530	Component: SVCTL_Job_Start_Command. As JobInfo giving to JSM_JobServiceManager is NULL.
CF533	Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
CF533	Component: ReportEventService. Category: RIP. Entity error: when CLITICAL ERROR occurred at ME access.
CF551	Component: MLPRN. Category: NetAppl. Task generation error.
CF551	Component: MLPRT. Category: NetAppl. Task generation error.
CF551	Component: EVR_LGS. Category: NetAppl. Task generation error.
CF610	Component: SSTUP. Category: OS. Error in the SystemStartUp (Thread generation, Entity data acquisition, DiskManager operation).
CF610	Undefined.
CF610	System Start Error.
CF615	Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access error).
CF620	Component: EventManager. Category: KM-Entity. Failed to obtain/receive event from framework.
CF620	Unable to Print.
CF620	System Error. Error acquiring the event data. Panel detects CF000 as same error.
CF620	System Error. Error acquiring the event data. Panel detects CF000 as same error. Unable to Load Files To CF Card.
CF630	Component: PowerManagement. Category: OS. Failed to mount or unmount during transition of the condition.
CF710	Component: IIS. Category: NetApl. Network file written error (inetd).
CF713	Component: IIS. Category: NetApl. Entity error (inetd).
CF720	Component: IIS. Category: NetApl. Network file written error (services).
CF723	Component: IIS. Category: NetApl. Entity error (services).
CF730	Component: IIS. Category: NetApl. Network file written error (snmpd).
CF733	Component: IIS. Category: NetApl. Entity error (snmpd).
CF743	Component: IIS. Category: NetApl. Entity error (hosts allow).
CF750	Component: IIS. Category: NetApl. Network file written error (hostname).
CF753	Component: IIS. Category: NetApl. Entity error (hostname).
CF760	Component: IIS. Category: NetApl. Network file written error (papd).
CF763	Component: IIS. Category: NetApl. Entity error (papd).
CF770	Component: IIS. Category: NetApl. Network file written error (cups).
CF773	Component: IIS. Category: NetApl. Entity error (cups).
CF780	Component: IIS. Category: NetApl. Network file written error (dhcclient).
CF783	Component: IIS. Category: NetApl. Entity error (dhcclient).
CF790	Component: IIS. Category: NetApl. Network file written error (smb).
CF793	Component: IIS. Category: NetApl. Entity error (smb).
CF7A0	Component: IIS. Category: NetApl. Network file written error (netware).
CF7A3	Component: IIS. Category: NetApl. Entity error (netware).
CF7B0	Component: IIS. Category: NetApl. Network file written error (ipfilter).
CF7B3	Component: IIS. Category: NetApl. Entity error (ipfilter).
CF7C0	Component: IIS. Category: NetApl. Network file written error (ethermode).
CF7C3	Component: IIS. Category: NetApl. Entity error (ethermode).
CF7D0	Component: IIS. Category: NetApl. Network file written error (other).
CF7D3	Component: IIS. Category: NetApl. Entity error (other).
CF7D7	Readout Error of SSL (authentication data).
CFAxx	HDD Error.
CFAxx	HDD Error.
CFA10	Component: OS_TOOLS. Category: OS. Error inside of hot plug detection thread, overwritten thread (failed to issue the event, failed to operate signal handler).
CFA20	Component: OS_TOOLS. Category: OS. Failed to obtain memory size.
CFA23	Component: OS_TOOLS. Category: OS. Access error to the Entity at master data stored area component.
CFA30	Component: OS_TOOLS. Category: OS. CF-DETECT OPEN error <0x07>.
CFA30	Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL error <0x08>.
CFA30	Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE error <0x09>.
CFA30	Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>.
CFA30	Component: OS_TOOLS. Category: OS. AES conversion IOCTL error <0x0b>.
CFA30	Component: OS_TOOLS. Category: OS. AES conversion CLOSE error <0x0c>.
CFA30	Component: OS_TOOLS. Category: OS. AES conversion command return value error <0x0d>.
CFA30	Component: OS_TOOLS. Category: OS. Message queue creation error <0x15>.
CFA30	Component: OS_TOOLS. Category: OS. Message queue Tx error <0x16>.
CFA30	Component: OS_TOOLS. Category: OS. Message queue Rx error <0x17>.
CFA30	Component: OS_TOOLS. Category: OS. Message queue deletion error <0x18>.
CFA37	Component: OS_TOOLS. Category: OS. Event Tx error <0x19>.
CFA43	Component: OS_TOOLS. Category: OS. Access error to the Entity at USB activation component.
CFB00	Component: Panel. Category: KI-Panel. Netfront error (SLIM_E_GENERIC).
CFB01	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_INVAL).
CFB02	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOSERVER).
CFB03	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_TIMEDOUT).
CFB04	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_DNS_NOTFOUND).
CFB05	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_OPEN).
CFB06	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_CONNECT).
CFB07	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_READ).
CFB08	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TCP_WRITE).
CFB09	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_CONNECT).
CFB0A	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_HANDSHAKE).
CFB0B	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_READ).
CFB0C	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_SSL_WRITE).
CFB0D	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQTIMEDOUT).
CFB0E	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSPTIMEDOUT).
CFB0F	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_NONE).
CFB10	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_CACHE_EXPIRE).
CFB11	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_UNKNOWN).
CFB12	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_NOHEADER).
CFB13	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_AUTH_FORMAT).
CFB14	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_FORMAT).
CFB15	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REDIRECT_CANCELLED).
CFB16	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_HEADER_SIZEOVER).
CFB17	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_BODY_SIZEOVER).
CFB18	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_RSP_HEADER_SIZEOVER).
CFB19	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_REQ_TOOMANYCONTINUE).
CFB1A	Component: Panel. Category: KI-Panel. Netfront error (SLIM_HTTP_E_TLS_INTOLERANT).
CFB1B	Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_OPEN).
CFB1C	Component: Panel. Category: KI-Panel. Netfront error (SLIM_FILEP_E_READ).
CFB1D	Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_SIZEOVER).
CFB1E	Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_NO_CONTENT).
CFB1F	Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYREDIRECT).
CFB20	Component: Panel. Category: KI-Panel. Netfront error (SLIM_CONTENT_E_TOOMANYAUTH).
CFB21	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY).
CFB22	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).
CFB23	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).
CFB24	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADURL).
CFB25	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_BADMIMETYPE).
CFB26	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_MIXEDSECURETYPE).
CFB27	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).
CFB28	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_INPUT_REQUIRED).
CFB29	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).
CFB2A	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).
CFB2B	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).
CFB2C	Component: Panel. Category: KI-Panel. Netfront error (SLIM_BROWSER_ERROR_KMC_SEGFAULT).
CFB2C CFB30 CFB31	Panel Error. NetFont error. Communication error between panel and main controller during initialization or rejection of communication by controller during initialization. Blue Screen of Death.
CFB30	Component: Panel. Category: KI-Panel. Failed to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CFB30	Incompatible Level Of Firmware on Main EEPROM.
CFB30	Incompatible Level Of Firmware on Main EEPROM.
CFB31	Component: Panel. Category: KI-Panel. Refused to connect the communication of the controller when starting up. Blue back screen. Cannot enter maintenance mode.
CFB31	Corrupt Firmware on Main EEPROM.
CFB31	Corrupt Firmware on Main EEPROM.
CFB32	Component: Panel. Category: KI-Panel. Time to start up request command (start up request command could not be received). Blue back screen. Cannot enter maintenance mode.
CFB32	Panel Error. Timeout request for start up command. Start command hasn't been received. Possible destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB33	Component: Panel. Category: KI-Panel. Cut off of the communication with the controller is detected - waiting to receive: select () OK return, recv() RX data length 0. Blue back screen. Cannot enter maintenance mode.
CFB33	Panel Error. Detects disconnection with controller. Possible overdrive of control board or destruction of system file in HDD. Cannot enter maintenance mode. Blue Screen of Death.
CFB34	Component: Panel. Category: KI-Panel. Time out for Response telegraphic message (could not receive response telegraphic message within a fixed time). In case on not through httpd, this error occurs (in case it does not become CGI time out).
CFB35	Component: Panel. Category: KI-Panel. Received abusive command from controller. At this moment, only the case that unexpected command comes in when wating for the startup request command.
CFB36	Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. select () function returned the error (other than EINTR).
CFB37	Component: Panel. Category: KI-Panel. Connection error is detected when waiting for he response telegraphic message from the controller. rcv () function returned the error.
CFB38	Component: Panel. Category: KI-Panel. Communication error is detected when transferring (using UNIX domain) response telegraphic message in the panel. send() function returned the error (other than EINTR).
CFB39	Component: Panel. Category: KI-Panel. Crucial error is detected when processing receive/transfer of the response telegraphic message from controller. Failed to acquire semafo???
CFB3A	Component: Panel. Category: KI-Panel. Communication error is detected when sending required response telegraphic message from panel. send() function returned the error (other than EINTR).